基于抛光基材的热蒸镀铜箔生长高平整单层石墨烯薄膜

在石墨烯的化学气相沉积工艺中,铜箔是决定石墨烯薄膜质量的重要因素。传统铜箔由于制备工艺的限制,存在大量的缺陷,导致石墨烯薄膜的成核密度较高。本工作选用抛光铝板、抛光不锈钢板、微晶玻璃和SiO₂/Si作为基材,用热蒸镀法制备了不同粗糙度的铜箔,并详细讨论了以该系列铜箔生长高平整度石墨烯薄膜的条件及铜箔对石墨烯薄膜品质的影响。实验结果表明,铜箔以(111)取向为主,与基材分离后,表面具有纳米级平整度。在生长石墨烯后,从SiO₂/Si剥离的铜箔成核密度是4种基材中最小的。同时,从SiO₂/Si剥离的铜箔晶体结构变化最不明显,具有良好的结晶性,表面几乎不存在铜晶界缺陷。当压强为3 000 Pa,氢气和甲烷流速分别为300 mL/min和0.5 mL/min时,可以获得约1 mm横向尺寸的石墨烯单晶晶畴。     

聚苯硫醚熔体的压致凝固行为

采用施加压力的方法将聚苯硫醚熔体凝固,凝固后获得的聚苯硫醚样品经过降温和卸压后在常温常压下回收. X射线衍射和差示扫描量热分析表明:约20 ms时间的快速压缩过程可以抑制熔体结晶,制备出非晶态聚苯硫醚块材,样品的表面及中心都是非晶态.非晶态聚苯硫醚的玻璃化转变温度和晶化温度分别为318和362 K.常压下的退火实验表明,非晶态聚苯硫醚在425 K等温结晶的产物为正交相晶型.压致凝固法中熔体的凝固不是靠温度变化,而是靠压力变化,样品表面和内部处在一致的温度下同时受压凝固,避免了热传导对非晶尺寸的影响,因此非常有利于获得结构均匀的大尺寸非晶态材料.     

Mechanistic model for the dielectric spectrum of a simple dielectric material

ABSTRACT

In this paper, we perform molecular dynamics simulations of a dielectric fluidic material composed of permanent molecular dipoles. The dielectric spectrum features two peaks at lower frequencies than the system phonon frequency. The primary peak is observed at all temperatures studied and shifts toward lower frequencies as the temperature decreases. During this shift, the secondary peak emerges with a higher peak frequency than the primary peak. The secondary peak amplitude increases as the temperature decreases. Both peaks are dependent on the wavevector; in the small wavevector regime, the primary peak is shifted to higher frequencies as the wavevector squared and the secondary peak amplitude increases as the wavevector increases, but shows no shift in frequency. From the polarisation balance equation, we propose a model for the dielectric spectrum. This captures the spectrum features, and we conjecture that the primary peak is due to dipole moment correlations (Debye-type) and the secondary peak is due to the correlation between the dipole moment and a microscopic local field.     

Gas-Sensing Activity of Amorphous Copper Oxide Porous Nanosheets

In this paper, the gas-sensing properties of copper oxide porous nanosheets in amorphous and highly crystalline states were comparatively investigated on the premise of almost the same specific surface area, morphology and size. Unexpectedly, the results show that amorphous copper oxide porous nanosheets have much better gas sensing properties than highly crystalline copper oxide to a serious of volatile organic compounds, and the lowest detection limit (LOD) of the amorphous copper oxide porous nanosheets to methanal is even up to 10 ppb. By contrast, the LOD of the highly crystalline copper oxide porous nanosheets to methanal is 95 ppb. Experiments prove that the oxygen vacancies contained in the amorphous copper oxide porous nanosheets play a key role in improving gas sensitivity, which greatly improve the chemical activity of the materials, especially for the adsorption of molecules containing oxygen-groups such as methanal and oxygen.     

CoFeSiB非晶丝弱磁场测量仪的研制

设计了以Co基非晶丝为敏感元件的传感器探头,多谐振荡励磁电路,信号处理电路,单片机显示电路,且对该磁场测量仪进行了标定。     

Can a Procedure for the Growth of Single-layer Graphene on Copper be used in Different Chemical Vapor Deposition Reactors?

In the last decade, catalytic chemical vapor deposition (CVD) has been intensively explored for the growth of single-layer graphene (SLG). Despite the scattering of guidelines and procedures, variables such as the surface texture/chemistry of catalyst metal foils, carbon feedstock, and growth process parameters have been well-scrutinized. Still, questions remain on how best to standardize the growth procedure. The possible correlation of procedures between different CVD setups is an example. Here, two thermal CVD reactors were explored to grow graphene on Cu foil. The design of these setups was entirely distinct, one being a “showerhead” cold-wall type, whereas the other represented the popular “tubular” hot-wall type. Upon standardizing the Cu foil surface, it was possible to develop a procedure for cm²-scale SLG growth that differed only by the carrier gas flow rate used in the two reactors.     

Highly selective hydrogenation of acetophenone over supported amorphous alloy catalyst

Alpha-phenylethanol (PE) is an essential chemical in the field of medicine and synthetic perfumery. Therefore, in this work, we used a supported Ni–B–P amorphous alloy catalyst (Ni–B–P/SiO₂) in the hydrogenation of acetophenone (AP) to α-PE, which demonstrated excellent catalytic activity and selectivity, compared with Ni–B/SiO₂ (KBH₄ reduction of nickel salt). Ni–B–P/SiO₂ exhibited a high AP hydrogenation conversion of approximately 99%, whereas the PE selectivity reached up to 94%, which is approximately 1.4-fold higher than that of Ni–B/SiO₂ (about 69%), thereby directly proving the unique inhibition of AP hydrogenation over hydrogenation of P in the Ni–B catalytic system. The doped P in Ni–B–P/SiO₂ enhances the oxidation resistance and maintains the valence stability of Ni and B. Furthermore, sufficient experimental data were collected to determine the kinetic parameters. Based on the Langmuir–Hinshelwood model, we assumed that (i) AP and H₂ compete for adsorption on Ni–B–P/SiO₂; (ii) AP has strong adsorptive capacity on Ni–B–P/SiO₂; and (iii) PE coverage on the catalyst was negligible. Then, the dynamic equation was derived, which indicated that experimental data agree well with the dynamic model. Finally, the activation energy was confirmed to be 50.73 KJ/mol. This report will open up an avenue for the industrialization of amorphous alloy catalysts.     

Targeted Construction of Amorphous MoSx with an Inherent Chain Molecular Structure for Improved Pseudocapacitive Lithium-Ion Response

Owing to low ion/electron conductivity and large volume change, transitional metal dichalcogenides (TMDs) suffer from inferior cycle stability and rate capability when used as the anode of lithium-ion batteries (LIBs). To overcome these disadvantages, amorphous molybdenum sulfide (MoS_x) nanospheres were prepared and coated with an ultrathin carbon layer through a simple one-pot reaction. Combining X-ray photoelectron spectroscopy (XPS) with theoretical calculations, MoS_x was confirmed as having a special chain molecular structure with two forms of S bonding (S²⁻ and S₂²⁻), the optimal adsorption sites of Li⁺ were located at S₂²⁻. As a result, the MoS_x electrode exhibits superior cycle and rate capacities compared with crystalline 2H-MoS₂ (e.g., delivering a high capacity of 612.4 mAh g⁻¹ after 500 cycles at 1 A g⁻¹). This is mainly attributed to more exposed active S₂²⁻ sites for Li storage, more Li⁺ transfer pathways for improved ion conductivity, and suppressed electrode structure pulverization of MoS_x derived from the inherent chain-like molecular structure. Quantitative charge storage analysis further demonstrates the improved pseudocapacitive contribution of amorphous MoS_x induced by fast reaction kinetics. Moreover, the morphology contrast after cycling demonstrates the dispersion of active materials is more uniform for MoS_x than 2H-MoS₂, suggesting the MoS_x can well accommodate the volume stress of the electrode during discharging. Through regulating the molecular structure, this work provides an effective targeted strategy to overcome the intrinsic issues of TMDs for high-performance LIBs.     

Development and validation of an ultra‐high‐performance liquid chromatography–tandem mass spectrometry method to determine the bioavailability of warfarin and its major metabolite 7‐hydroxy warfarin in rats dosed with oral formulations containing different polymorphic forms

A simple, sensitive and rapid ultra‐high‐performance liquid chromatography–electrospray ionization–tandem mass spectrometry method was developed and validated for the quantification of warfarin and 7‐hydroxy warfarin in Sprague Dawley (SD) rats. Animals were administered a single dose of warfarin sodium formulations (crystalline and amorphous) at 12 mg/kg via oral gavage and blood was drawn over a 96‐h time course. Sample process recoveries, matrix effect and analyte stability were determined. The linearity for warfarin and 7‐hydroxy warfarin was from 5 to 2000 ng/mL in blank SD rat plasma. Correlation coefficients (r²) for standard calibration curves were >.98 and analytes quantified within ±15% of target at all calibrator concentrations. The average percent accuracy and precision for intra‐ and inter‐day were 93.7%–113.8% and ≤12.1%, respectively, for warfarin and 7‐hydroxy warfarin, across the quality control standards (5, 10, 500, 1800 and 2000 ng/mL). Acceptable analytical recovery (>55%) was achieved with process efficiencies >41.5% and matrix effects <139.9% over the analytical range. Both analytes were stable in stock solution, autosampler, benchtop and three cycles of freeze–thaw with percent accuracy ≥90.2% and precision (percent relative standard deviation) ≤14%. The validated method was successfully applied to a pre‐clinical bioavailability study of crystalline and amorphous warfarin sodium formulations in SD rats.     

以尿素为氮源合成AlN粉体过程中非晶碳的石墨化

针对有机合成过程中碳及碳化物的残余,传统方法中普遍使用除碳的工艺,而很少有文章针对非晶碳的结构和形貌进行表征。为此,本文采用高尿素含量的前驱盐体系,通过在氮气保护气氛中煅烧获得AlN粉体。采用X射线衍射分析、红外和拉曼光谱分析、扫描电子显微镜和透射电子显微镜对850~1 500 ℃温度范围内煅烧获得产物的结构和形貌进行表征,对AlN合成过程中含碳产物结构形貌的变化,以及AlN和含碳产物之间相互的依存生长关系进行分析。结果表明,AlN生长的过程中伴随着无定形碳的石墨化转变,AlN颗粒的形貌也受含碳残余产物形貌的影响而出现有规律的变化。